TurboCharge Fast Charger 67.2/84.0V for 60/72V GX16-3F 5/6A [YZ500]

• TurboCharge Fast YZ is eSN's fast charger for 60 and 72 volt systems, offering:
  • Built-in display showing voltage and charging current.
  • Dual fan design, quieter than typical (such as TurboCharge MC).
• Available in two voltage variant:
  • YZ50060 67.2V 6A (403.2 watts) for 60V system.
  • YZ50084 84.0V 5A (420.0 watts) for 72V system.
• Fitted with GX16 3-pin female plug (as pin 1 +ve, pin 3 -ve) which was the predominate connector adopted by most common makes and models prior to 2025. Designated as GX16-3F-13, implemented on early models of NAMI Burn-e and Kaabo (Mantis & Wolf), all VSETT (non-Apex) & Zero. GX16-3F was also implemented on early 48V & 52V models such as Kaabo and Dragon GTS/GTR/Cyclone Series (with varying [12] and [13] pinouts) and all Zero & VSETT (non-APEX). Image below shows GX16 3-pin connectors, (left) the male charging port panel socket (on eScooter) and (right) the female plug (on charger cable). Image is from the GX16 product page.
  
  
  eSN optional Conversion Cables (CC):
  
  • If pin 1 +ve, pin 2 -ve configuration is required (e.g. older models of Dragon Predator, Lightning V2, Beast & EMOVE Cruiser) add GX16-3F conversion cable, variant: GX16 3-Pin Female [12] from GX16 3-Pin Male [13].
    This will route the -ve (negative) through pin 2 instead of pin 3.
  • Later model eScooters adopt a black plastic moulded connector where the plug on the charging cable is male. If this type is required, add GX16-3M conversion cable to suit the charging port of your eScooter or consider a TurboCharge charger that has the type-specific (private label) native connector. Makes with such connectors include Dragon/Langfeite (YJ20), NAMI (RGX16-2) , Kaabo (LT) & Teverun/Dualtron (BM).
• Input cable accepts 110-240 volts. Hard wired cable with Australian 3-pin power cable (1.4 meter length).
• Output cable 2 x 1.0m² cores with generous 1.1 meter length. In contrast, the TurboCharge MC model has 2 x 1.5mm cores.
• 2 x 40mm fan (secured with 2 screws each, located at each end). Slightly quieter than TurboCharge MC. LED charging status indicator switches from green to red when charging.
• Chargers have certification to ISO testing, those required for EESS Australian compliance for Regulatory Compliance Mark (RCM) with appropriate proof of RCM compliance certification.
• YZ series is to 450 watts (standard escooter chargers are typically 130 watts). Manufactured by YZPOWER - Guangzhou Yangzi Power Supply Co., Ltd. for custom order spec by eScootNow.
• Weight with cables 1.15kgs in a flat form factor 208mm x 123mm x 55mm silver colour alloy enclosure (120 grams lighter than TurboCharge MC).
• For your safety, include your scooter's make / model / serial / voltage and battery Ah capacity as order comment on checkout so that the appropriate voltage can checked to best of our ability as part of order fulfilment. Remember some makes have models that are available in variants that have different voltages and inappropriate selection of higher voltages is a common cause of thermal runway and house fires folks.

Notes:

1. The two buttons adjacent to the display are not enabled. They are reserved for the adjustable model (voltage/current).
2. Output (current) is identical for both 110 and 240 volt use.
3. Although "fast chargers" are quick, they typically do not exceed the recommended charge rate of the cells, except for small capacity batteries (e.g. Chinese 18Ah packs). You may also need to check the internal fuse in the scooter is sufficiently rated as many are by default only 5 amp which only caters for stock 2 amp chargers.
4. YZ series also retailed in our region by Cap Rouge who accommodate the common eBike plugs/connectors.
5. Comparative image of this charger with the TurboCharge MC (black enclosure, white label) and the factory stock NAMI charger. Note the presence of switch on the Fast MC, largest fan, largest ventilation and smallest footprint. QC has two smaller fans, largest footprint.
   
   
6. Part of the eSN's TurboCharge range.
   
   
7. Regulatory Compliance Mark (RCM)
   
   The Electrical Compliance Mark indicates compliance with EESS (Electrical Equipment Safety Scheme). For electrical safety, in-scope electrical equipment must not be sold unless the item is marked with the RCM in compliance with AS/NZS 4417.1 & 2.
   Responsible Suppliers, equipment and certifications (including certificate number) of are registered with Electrical Regulatory Authorities Council (ERAC).
   There is a public search tool to check registration and compliance, the Certificate Number is printed underneath the RCM logo on equipment nameplate which looks like this:
   
   EARC Equipment safety requires an Australian based assessor to issue certificate of RCM compliance. The assessment considers a number of standards and guides such as::
   • Australian/New Zealand Standards:
     (i) AS/NZS 3000, Wiring Rules.
     (ii) AS/NZS 3820, Essential safety requirements for low voltage electrical equipment.
     (iii) AS/NZS 4417, Marking of electrical products to indicate compliance with regulations AS/NZS 4417.1, Part 1: General rules for use of the mark.
     (iv) AS/NZS 4417.2, Part 2: Specific requirements for electrical safety regulatory applications.
   • International Standards and Guides (mostly ACMA for EME):
     (i) ISO/IEC 17000, Conformity assessment -- Vocabulary and general principles.
     (ii) ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories.
     (iii) ISO/IEC 17050, Conformity assessment - Supplier's declaration of conformity.
     (iv) ISO/IEC Guide 2, Standardization and related activities -- General vocabulary
     (v) ISO/IEC Guide 65, General requirements for bodies operating product certification systems.
     (vi) ISO/IEC Guide 67, Conformity assessment – Fundamentals of product certification.
     (vii) Joint Accreditation System of Australia and New Zealand.
     (viii) JAS-ANZ Procedure 15, General Requirements for Bodies operating Product Certification Systems (identical to IAF GD 5).
   Certificate (approval #): AZ 69024861
   Applicant (certification): TüV Rheinland Australia Pty Ltd
   Brand/Trade Name: Yangzidianyuan
   Model Number: YZ50012, YZ50016, YZ50024, YZ50036, YZ50048, YZ50060, YZ50072, YZ50084
   Equipment Class: Level 3
   Certificate Holder: Shenzhen Yangzi Power Co.,Ltd.
   Status: Approved
   Expiry Date: 29/01/2026
   
   
8. Voltage reference chart: