Electric Brake Hall Sensor Switch suits Hydraulic Levers of TurboBrake, Zoom & Langfeite/Dragon (e.g. Predator/Hurricane)

Name: Electric Brake Hall Sensor Switch suits Hydraulic Levers of TurboBrake, Zoom & Langfeite/Dragon (e.g. Predator/Hurricane)
SKU: BRAKE-SWITCH
Price: 15.0 AUD
Availability: InStock

SKU BRAKE-SWITCH/M8-050

AU$15.00

Bulk pricing available for quantities of 2 units or more

Also suits Kaabo Wolf, Mantis Pro, VSETT, most Dragon models including smaller M6 Predator and Hurricane.

Variant

M8 50mm as Zoom Kaabo Factory Spare

M8 150mm as TurboBrake Spare

M8 300mm as TurboBrake / Zoom Spare

M6 100mm as TurboBrake Spare

In stock: 45 available

Quantity:

Buy more, save more

Quantity	Price per item	Discount
2 items	AU$12.73	15% off
6 items	AU$11.36	24% off

Save this product for later

Customer reviews

Reviews only from verified customers

No reviews yet. You can buy this product and be the first to leave a review.

Electric Brake Hall Sensor Switch suits Hydraulic Levers of TurboBrake, Zoom & Langfeite/Dragon (e.g. Predator/Hurricane)

Product Details

Brand: Kaabo

Electric brake hall sensor switch suits Hydraulic levers of:
- Zoom such as those on Kaabo models of Mantis & Wolf, earlier model Dragon Lightning (including V2), Dragon Slayer and most (the non-NUTT) models of VSETT such as 10+ & Zero such as 10X hydraulic models.
- TurboBrake, such as HB427-H calliper models of:
  - Teverun (including models of Blade and Fighter).
  - Dragon / Langfeite models with on Predator, later models of the Cyclone Pro, Hurricane, Lightning & The Beast. See note regarding M6/M8 connector.
  - and of course eSN TurboBrake levers.
Available in three variants, choice of M8 (8mm - most common) or M6 (Later models of Dragon Langfeite & InMotion):
- M8 2-pin red male with 50mm cable - as Zoom Kaabo Factory Spare.
- M8 2-pin red male with 300mm cable - as Zoom / TurboBrake Spare.
- M6 2-pin red male with 300mm cable - as TurboBrake Spare.
Mechanism uses magnetics with a two wire hall effect sensor, responsible for informing the controller of the position of the brake lever which activates electric braking and brake light. If problematic, electric brake and brake lights may not respond as expected when engaging brake lever, or the switch could be applying brake continuous or intermittently when lever is not engaged. To operate effectively, it needs be calibrated - see notes below. If calibration does not restore operation, and it fails continuity test on multimeter, replace the switch.

Adopts the common convention used amongst nearly all eScooter makes and models being normally open. This means when lever is not engaged, the circuit is open ("off"). When engaged (pulled) the circuit closed (switch is "on"). Closer type.

Notes:

Switches needs be calibrated periodically as pads wear or brakes are serviced. Prior to adjusting or removing existing switch, ensure you backing off the grub screw that secures the connector.
The hall type switch uses magnetics therefore be mindful of the lever's proximity to other magnetic fields such as that from throttle. Close lever-throttle proximity can cause unexpected signalling - move or disconnect the throttle.
To troubleshoot, you can temporarily fit the switch from the other lever, check continuity with meter and check 5v is being delivered to it. Signal output of two wire IC's is via different current levels, a multimeter on continuity mode is usually sufficient test.
Note the newer Dragon Langfeite models (e.g. Predator, Hurricane and later models of Lightning & The Beast) use a smaller M6 connector plug. M6 is less common. Length of 120mm. We also stock M8 cables. There is no polarity applicable so it is a simple matter of joining each of the two wires and it is best practice to have some sort of plug so you can disconnect if necessary.
This switch appears similar to that on earlier (older) the Logan levers as both have a 6.2mm diameter. The notch/key on earlier Logan type is longer and narrower than this Zoom/TurboBrake type. The Logan variant is available here.
Refer to Kaabo Spares Category Home Page for wiring diagrams.
These videos demonstrate how to calibrate / replace (not Logan specific). It is best to just work on one side, over the course of several rides so it has bedded in prior to making changes to the other side. eSN recommends having the ebrake switch engage first (early) then as the lever is further depressed the physical pads engage. Allowing the electric brake to fully engage prior to physical brake pad engagement improves braking stability, reduces brake wear and reduces heat.
1. Video showing replacement of switch on NAMI Klima (Logan Lever) from Epic Cycles:
2. Video showing the replacement of switch on NAMI Klima (Logan Levers) from Halbknapp E-Scooter Shop:
3. Video showing general calibration process on a XOD Lever from VoltiBike
4. Video showing calibration from Alter Ego Electric Bikes

Extensive online catalogue exclusively Now Club members & ABN/trade | eSN2026#JP-CN | Group Ride Guide | On The Run Workshop |

eSN Ops Dash: ⚠︎ Red - delayed fulfilment